Leave a long enough tail on your tag line attachment so that you can thread the fixed rappel station and connect your ropes before you disconnect from the tag line and undo what ever knot you used to tag the line. Zero chance of dropping your tag line is a good thing!
Affiliate links above support the content created here. Making a purchase through one of them earns the author a small commission on no additional cost to you. Thank you!
The Redirected Clip-Back Lower provides a smooth lower and the rope will stay twist free if you keep the rope running inline with the belay device. This method works with any tube style belay device like the Black Diamond ATC or the Petzl Verso. Don’t forget to add a third hand friction knot on off your belay loop to the brake strand and close your system!
First install the rope onto your tube style belay device as if you were about to belay your partner from your harness. Instead of attaching the belay carabiner to your belay loop, attach it to the master point of your anchor.
Redirect the brake strand through the same locking carabiner so that the brake strand is coming out of the carabiner on the same side as the load strand.
Before lowering attach a third hand fiction hitch to the brake strand and attach that to your belay loop with a locking carabiner.
Make sure the system is closed (either you are tied into the other end of the rope or it is knotted near the end). If your rope is already stacked you are now ready to lower.
Disclaimer: Climbing is dangerous. Practice in a safe setting and seek qualified mentors, instructors, and guides.
Questions or Comments? Please share them below!
See you in the mountains,
Northeast Alpine Start
Affiliate links above support the content created here. Your purchase after visiting these links will earn the author a small commission at no additional cost to you. Thank you!
There are many reasons why a climbing party may choose to lower a team member during a descent, for example, very windy conditions. While the Munter Hitch only requires a single HMS style locking carabiner the “Redirected Plate” method is another option that only requires a tube style belay device like the Black Diamond ATC or the Petzl Verso and two locking carabiners (or one if lowering through fixed chains).
This method provides one of the smoothest lowers and is probably the easiest to make sure the rope stays twist free.
First install the rope onto your tube style belay device as if you were about to belay your partner from your harness. Instead of attaching the belay carabiner to your belay loop attach it to the master point of your anchor.
Redirect the brake strand through a locking carabiner in the master point of your anchor. It is best if this locking carabiner is slightly smaller than the belay locking carabiner.
Before lowering attach a third hand fiction hitch to the brake strand and attach that to your belay loop.
Make sure the system is closed (either you are tied into the other end of the rope or it is knotted near the end). If your rope is already stacked you are now ready to lower.
An efficient use of this technique when rappelling with a single rope is to thread the rope through the fixed gear as the redirect instead of a locking carabiner. That way when the climber reaches the ground, or the next anchor, you can pull more rope through to the middle mark of your rope, remove your tube style device, put yourself on a double strand rappel, and head on down. Or even more crafty conduct a “Reepschneur” Rappel <- upcoming tech tip!
Disclaimer: Climbing is dangerous. Practice this technique in a safe setting and seek qualified mentorship and instruction.
Questions or Comments? Please share them below!
See you in the mountains,
Northeast Alpine Start
Affiliate links above support the content created here. When you make a purchase after using one of those links the author earns a small commission at no additional cost to you. Thank you.
The Munter Mule Overhand or “MMO” is a combination of three knots that creates a releasable-under-tension method of securing a rope or cordelette. The MMO is useful in improvised self-rescue applications most often involving load transfers. In this situation I was using it to secure one end of a typical top-rope setup so my guest could practice rope ascension on the other end of the top-rope. The context here is if the climber practicing rope ascension gets a device jammed or has trouble transitioning from ascension back to descending I can remove the overhand, carefully deconstruct the Mule, then use the Munter to lower the climber back down to the ground.
Climbing is dangerous! Be sure to seek qualified instruction and practice new skills on the ground.
Questions or Comments? Please share them below!
See you in the mountains,
Northeast Alpine Start
Affiliiate links above support the content created here. When making a purchase through these links the author earns a small commission on no additional cost to you. Thank you.
I’ve now had the Petzl Neox for about two weeks and have been able to form some opinions and test it in applications I’m most interested in. The most recent day I spent at the cliff with it was focused on seeing how it performed as a progress capture in an improvised hauling system and in a rope ascension system. Both these uses are important to me for assisting a seconding climber or rescuing an injured lead climber, and places where I would traditionally be using a Petzl GriGri. Here is some raw footage of this round of testing and some of my thoughts.
I assumed the Petzl Neox would work great for progress capture in this systems due to the spinning internal cog wheel and it definitely felt efficient in both the hauling scenario and the rope climbing scenario. I will be doing another round of comparisons with a more realistic full body weight load on the system but the fact the wheel still spun in my rope ascension test leads me to think it will still spin with a full load in a hauling system. This took me a little while to wrap my head around because you can seen when the device sees a full load while single strand rappelling the cam rotates, the wheel stops spinning, and you control your descent with the friction of the rope moving through the created bend. Why wouldn’t the wheel rotate and lock like that while using it as a progress capture?
The answer comes down to physics and while not having anything close to a degree in physics I can see how the device isn’t getting the full load in these scenarios. The full load is on the “tractor”, or friction hitch, or the Petzl Tibloc. When you go to pull slack through the Petzl Neox at that part of the cycle there is almost no weight on the device so the cam does not engage and the wheel spins freely reducing effort in hauling and ascending. When you relax during the hauling process all the load goes back to the Petzl Neox and the cam engages. Same with ascending, when you transfer your weight from your foot loop back to your harness the necessary threshold is exceeded and the cam engages. When you put your weight into your foot loop to progress the weight comes off the device and it is easier to pull the slack through the device then the Petzl GriGri.
Summary
It is still early in our broader exposure to this new belay device but the videos have been pouring out from influencers, highly certified guides, and rock star YouTuber’s. My opinion will likely evolve over the course of the summer as I put more days on the device, and expose more beginner climbers to it. For now I will re-iterate that I really like how easy it is to pull slack while belaying from above, and the more I think about it I do think this device may be in someways safer for a newer belayer as the instructions basically encourage you to not tough the device while paying out slack. This device may help prevent the holding open of the cam at risky moments which was likely part of the motivation of the anti-panic feature that came with the Petzl GriGri+.
Exclusive Discount with HowNot2.com!
I am really excited to announce I’ve partnered with HowNot2.com and can now offer my followers a 10% discount on anything you purchase at hownot2.com and support what I am doing with discount code “NEAlpineStart” <- capitalization does not matter!
See you in the mountains!
I hope this information is helpful for your to make an informed decision. While Petzl supplied me with a Neox to review this is not a sponsored post. Affiliate links above help me continue to spend time creating these videos and posts and I thank you for your support!
Today I was able to get out to the cliff for a short bit to check out the newly released assisted blocking belay device, the Petzl Neox.
This is not a full in-depth review. It is a preliminary look at this new option in assisted blocking belay devices and I try to distinguish some of the obvious differences in the Petzl Neox, the Petzl GriGri, and the Petzl GriGri+. As time allows I will be diving more deeply into the topics I mention in the video. In the meantime please check out my initial thoughts and if you haven’t already please subscribe to the YouTube channel so I can keep sharing this type of content with all of you!
See you in the mountains,
Northeast Alpine Start
Affiliate links above support the content created here. Making a purchase after visiting one of these links earns the author a small commission at no addition cost to you. Thank you!
The Munter Hitch is one of the most valuable knots used in climbing and every climber should become familiar with this versatile hitch. While Werner Munter didn’t invent the hitch, a few Italian’s did in the 1950s, he was the one who popularized it in the 1970s and why it bears his name. This hitch works best on a large pear shaped locking HMS style carabiner like a Petzl Attach or Petzl William Screwlock Carabiner. Fun fact, the “HMS” is a German abbreviated for “Halbmastwurfsicherung” which translated means roughly “half a clove hitch” which describes the structure of this hitch. You can read more on this history of the hitch here.
Formation
To tie the Munter Hitch you form a twist in the rope similar to the Clove Hitch and drop a strand into the carabiner as well. It is really easy when learning this hitch to remove the twist when you add the second strand which leaves you with the rope just double looped through the carabiner which should be obviously incorrect. Watching a few videos of how to tie it along with plenty of practice tying it inside your home or on the ground should proceed you tying it for real life application.
One of the cool aspects of the Munter Hitch is that it is “reversible”, meaning it will flip through the carabiner into a different orientation depending on which strand is being loaded. During instruction we use the terms “load” strand and “brake” strand. If you only apply load to the “load” strand the hitch will end up in what is referred to as the “lowering” orientation. If we only apply load, or more commonly pull in slack while belaying, the hitch will flip through the carabiner into what is referred to as “belay” orientation. Generally when creating the Munter Hitch it is common to create an “air” hitch like demonstrated in the above video and then install it onto the carabiner. With a little practice it becomes efficient to tie the hitch directly onto the carabiner.
Advanced Formation
For those with a strong grasp on the basic ways to form the hitch it can be useful to learn how to tie the hitch onto the carabiner in the orientation it will first be operated. For example tying it so it is already in belay orientation, or tying it is it is already in lowering orientation. These methods can add efficiency especially when progressing to advanced self-rescue skills and for those seeking out guiding certifications in rock and alpine guiding.
Application
Belaying– The most common use for the Munter Hitch is an alternative to a plaquette style belay device like a Petzl Reverso or Black Diamond ATC Guide when belaying a second directly from the anchor. This choice may be because of a dropped belay device, or it may be for speed and efficiency, or it may be out of necessity (ice’d up frozen ropes while ice climbing can work better in this hitch and be near impossible to install into a plaquette).
Lowering– The smoothest way to lower a climber directly from above is by using a Munter Hitch and lowering directly from an anchor. A common misconception is this method will twist your rope up and/or greatly wear your rope as the hitch rubs on itself. Both of these conceptions are false with proper use of the hitch, which primarily means keeping the orientation of the BRAKE strand PARALLEL to the LOAD strand while lowering. Doing so will prevent any twisting of rope. The second consideration is conducting a smooth, steady, non-high speed lower. This will not damage the rope and modern rope have sheaths that can easily handle the minimal wear using this hitch hundreds of times will put on your rope. It is a good practice to use a “third hand” friction hitch on the brake side of the hitch connected to your belay loop while conducting anything but the shortest and simplest of lowers.
Rappelling– While it is possible to rappel short distances with the Munter Hitch attached to a locking carabiner on your belay loop it is a bit awkward to do so and the dramatic difference in angle that the two strands leave the hitch leads to massive rope twisting (and where this hitch probably got a misguided bad-wrap). In truth if you rappel by holding your brake strand parallel to the rope you can manage this without twisting your rope but this practice is very unintuitive to other modes of rappelling and I would only use it as a last resort.
Summary
The Munter Hitch should be in your top five familiar climbing knots. From belaying to lowering it has a lot of applications in climbing, especially in the self-rescue world when we start looking at tension releasable solutions (coming soon). If you haven’t used this hitch in your climbing take sometime to build it at home and see how it operates. Even with all the advanced and great belay devices on the market it is wise to have a fall back plan that only requires a single locking carabiner.
See you in the mountains,
Northeast Alpine Start
Affiliate links above support the content created here. Making a purchase through on of those links earns the author a small commission at no additional cost to you. Thank you!
On April 28th, 2024 a climber fell almost 400 feet sustaining serious injuries when their rappel system failed. The suspected mechanism of failure was an improperly threaded girth hitched rappel ring. In this video I demonstrate how this occurrence is possible.
Some key take home points;
For better and/or worse we are seeing girth hitched rappel rings on fixed rappel anchors
Careful inspection of the hitch and proper placement of your threaded rope is CRITICAL
Best practice is to ALWAYS stress test your rappel connection BEFORE you remove your lanyard from the anchor.
Alpine Savvy also has a nice post with more information and some opinions on this situation here.
See you in the mountains,
Northeast Alpine Start
Psst… You can get 10% off Rocky Talkies with “AlpineStart10” at this link!
Affiliate links above support the content created here. When you make a purchase through one of these links the author receives a small commission at no additional cost to you. Thank you.
The Clove Hitch is the most common knot used to secure oneself to an anchor and in this video I share the multiple ways I have learned to tie this excellent hitch.
The first method I learned was to create the two asymmetrical loops and then “slide” the loops in front or behind each other. Then I learned the “crossed” hands method which takes a little practice but once you get it dialed it is a very fast way to form the hitch. The one-handed clove hitch is a bit of a party trick but still fun to learn. Finally learning to tie the clove hitch directly onto a carabiner with one hand is a worthwhile skill to master as you can increase your security on a small stance by holding onto the anchor with your off hand. I use this method most often while ice climbing but it’s useful in any climbing context.
One tip to assist learning how to tie the clove onto a carabiner is to just start with a clove hitch already on the carabiner, and then slowly “deconstruct” the hitch only strand at a time. Then build the hitch again, and deconstruct again, and repeat until the muscle memory is gained!
While you can also tie a clove hitch around a solid object, like a tree, I’ve never found a practical use for that method in the climbing world, so I do not demonstrate it here.
How do you like to tie your clove hitch? Know any other methods that I haven’t listed here?
Affiliate links above support the content created here. Making a purchase through one of those links earns the author a small commission at no additional cost to you. Thank you.
The first knot most climbers learn is the “Retraced Figure Eight” knot. While a minority of climbers choose to connect the rope to their harness with a double bowline knot most of the climbing guides and instructors I have met greatly prefer to the more easily recognizable Figure Eight. Since there are a few ways to create a retraced Figure of Eight there is only one way that is becoming more known as “ideal”. When all these points are met I refer to this as the “Optimized” Figure Eight Knot.
Only the amount of rope needed to create the knot is used
The loop that has captured the harness tie-in point is no larger then the belay loop
All the strands are parallel with no cross overs
After all four strands exiting the knot are “dressed & stressed” there is only 6 inches of tail
The load strand entering the knot ends up on the “inside” of the knot
Your partner checks your knot before you start climbing
In this video I demonstrate the methods I use to tie this correctly each time.
There is a really in-depth look at this by “Hard is Easy” on YouTube here, though I use a mirror image of his method to achieve the same result. There are also some great pictures showing some of the nuances over at Alpine Savvy.
Do you tie your eight like this? Any questions or comments? Please let me know below!
See you in the mountains,
Northeast Alpine Start
Affiliate links above support this blog. Making a purchase through one of them will earn the author a small commission at no additional cost to you. Thank you.
